PowderMEMS® micromagnets for integrated magnetic field sources

Integrating Magnetic Fields Directly into Microchips

Many microelectronic devices require a defined permanent magnetic field. In magnetic field sensors, for example, this field can establish the operating point or enable motion detection.

Such sensing principles are used in applications including rotational speed and current measurement.

Separate Magnets Limit Miniaturization

Conventional permanent magnets are manufactured separately and subsequently assembled onto the microchip. This approach becomes increasingly challenging as devices continue to shrink.

Assembly requires additional space and increases the complexity of the overall design. At the same time, the magnet must be positioned with high precision relative to the active sensor structure, as even small deviations can alter the resulting magnetic field.

Conventional Microfabrication Processes Reach Their Limits

Established manufacturing techniques offer only limited possibilities for integrating three-dimensional permanent magnets directly into a substrate.

Physical vapor deposition and electroplating are restricted in terms of material selection and achievable layer thicknesses. Sintering requires temperatures that can be problematic for electronic components that have already been fabricated.

Polymer-bonded magnetic materials, in turn, impose specific requirements on filling processes, viscosity, and the prevention of air inclusions, particularly for structures in the submillimeter range.

Quantum Technologies Require Particularly Precise Magnetic Fields

Quantum sensors based on nitrogen-vacancy (NV) centers in diamond require a highly stable magnetic field at the diamond surface. Fluctuations in this field can affect measurement accuracy.

Precisely controlled magnetic fields are also relevant for trapped-ion quantum computers, for example, to address individual qubits using spatial variations in the magnetic field.

This creates a growing demand for magnetic structures that can be positioned with high precision and, in the future, manufactured in larger quantities.

Goal: Manufacturing Magnets Like Microstructures

PowderMEMS® therefore takes a different approach: Rather than being assembled as a separate component at a later stage, the magnet is fabricated directly within the substrate during the microfabrication process.

The shape, position, and number of magnets are defined during wafer design.

Fabricating Micromagnets Directly in the Wafer

PowderMEMS® is a technology developed at Fraunhofer ISIT for manufacturing three-dimensional functional structures from powder materials.

For micromagnet fabrication, magnetic powders are introduced directly into predefined cavities in silicon, glass, or ceramic substrates and subsequently consolidated into stable structures.

Defining Magnet Geometry Through Lithographic Structuring

First, cavities with the desired geometry are fabricated in the substrate.

This means that the position and geometry of the resulting micromagnets are determined during the microstructuring process. Depending on the geometry, the resulting magnetic field can also be tailored.

Automated Magnetic Powder Filling

The cavities are filled with dry magnetic powder. The process is established for permanent magnets based on neodymium-iron-boron (NdFeB).

Automated filling makes it possible to fabricate a large number of magnetic structures across an entire wafer in a single process step.

Consolidating Powder at Low Temperatures

The loose powder is consolidated into a mechanically stable structure using atomic layer deposition (ALD).

A very thin ceramic coating surrounds the individual powder particles and bonds them together. No high-temperature sintering process is required.

Co-Designing Geometry and Magnetic Field

The micromagnets are designed using computer simulations. This makes it possible to investigate which magnet shape and position will generate the magnetic field required for a particular application.

The fabricated structures are subsequently characterized experimentally and compared with the simulation results.

Exploring Additional Magnetic Materials

Current development activities also focus on samarium-cobalt (SmCo). Compared with NdFeB, this material exhibits lower temperature-dependent magnetic drift, making it attractive for applications involving varying operating temperatures.

Another development objective is multiaxial magnetization, which is intended to enable more complex magnetic configurations to be realized directly within the substrate.

Wafer-Level Micromagnet Fabrication Using Semiconductor Processes

PowderMEMS® combines established semiconductor structuring techniques with automated powder integration and atomic layer deposition. The process is integrated into a 200 mm manufacturing line, enabling the fabrication of numerous precisely defined magnetic structures on a single wafer.

Supporting Different Substrate Materials

PowderMEMS® micromagnets can be integrated into a variety of substrates:

  • Silicon
  • Glass
  • Ceramics

Glass structuring further expands the process capabilities, particularly for quantum technology applications such as trapped-ion systems.

Automated Wafer-Level Powder Filling

Automated powder filling of complete wafers was developed in collaboration with Fraunhofer IFAM.

Depending on the design, hundreds to thousands of magnetic configurations can be fabricated per wafer.

Low-Temperature Processing for Flexible Integration

ALD-based solidification takes place within a low temperature range of approximately 80 to 300 °C.

This allows micromagnets to be integrated before, during, or after other steps in device fabrication, depending on the process chain. The approach thus also offers potential for post-CMOS integration.

Fabricating Structures from Micrometers to Millimeters

 

The process covers feature widths ranging from approximately 20 µm to 4 mm.

The feature thickness can reach several hundred micrometers. For example, on a standard 200-mm wafer, thicknesses of up to 650 µm are possible.

Positioning is performed with an accuracy of a few micrometers.

 

Comprehensive Magnet Characterization

Various analytical techniques are combined for development and validation:

  • Magnetic field measurements
  • Electron microscopy
  • X-ray computed tomography
  • Computer simulations of magnetic fields

Technical data for PowderMEMS® magnets made of NdFeB specify a remanence of approximately 0.55 tesla at room temperature.

Investigations have been conducted over a temperature range from −268 °C to +150 °C.

Generating Precise Magnetic Fields Exactly Where They Are Needed

Substrate-level integration makes it possible to position micromagnets directly next to sensors, MEMS devices, or quantum systems. This allows the magnetic field source to be incorporated into the device design from the outset.

Magnetoresistive Current Sensors

Integrated PowderMEMS® magnets were investigated as a local magnetic field source for magnetoresistive sensors.

A prototype modeled after a mass-produced product was developed in collaboration with Sensitec GmbH. The integrated magnets replace separately mounted magnets. The performance is largely on par with that of the mass-produced version.

 

3D Hall Sensors

In collaboration with Fraunhofer IIS, a 3D Hall sensor with an integrated magnet on the back of the chip was demonstrated.

The design has a height of less than 1 mm and was used for contactless speed measurement on a gear.

 

NV Quantum Sensors

In collaboration with the CiS Research Institute for Microsensors, the integration of micromagnets for quantum sensors based on NV centers was investigated.

In the proof-of-concept experiment, a magnetic field within the required range was generated. The measured field matched the simulation and an independent measurement.

Trapped-Ion Quantum Computers

In collaboration with eleQtron, glass-based ion traps featuring integrated micromagnets were realized as a demonstrator.

In this application, the integrated magnets are particularly relevant for generating precisely defined localized magnetic field distributions.

Energy Harvester

PowderMEMS® micromagnets have also been investigated in fully integrated microelectromechanical energy harvesters.

Magnetic coupling enables contactless excitation of the mechanical structure.

Mechanical Magnetic Field Sensors

Further research has demonstrated the integration of micromagnets into mechanical magnetic field sensors.

The application range therefore extends from conventional semiconductor sensors to mechanical and quantum-based sensing principles.

Industries and Future Applications

Key application areas include:

  • Automotive and electric mobility
  • Industrial and power electronics
  • Consumer electronics
  • Quantum sensing and quantum computing
  • Navigation and safety systems

In general, this approach targets microdevices that require a precisely defined, localized permanent magnetic field.

Integration Eliminates the Need for Separate Magnet Assembly

PowderMEMS® shifts magnet fabrication from a subsequent assembly step into wafer-level processing. This allows the magnet and the microdevice to be designed together from the outset, offering advantages in terms of space requirements, positioning accuracy, and reproducible manufacturing.

Precisely Positioning Magnets Relative to the Device

The magnet position is defined during substrate microstructuring rather than in a subsequent component assembly step.

This enables magnetic structures to be positioned relative to the functional structures of the chip with an accuracy of a few micrometers.

Reducing Device Size

The magnet is integrated directly into the substrate and therefore requires no separate mounting space.

The demonstrated 3D Hall sensor, for example, achieves an overall device height of less than 1 mm.

Fabricating Numerous Magnets Reproducibly on a Single Wafer

Hundreds to thousands of magnetic configurations can be fabricated within the same wafer process.

Since geometry and position are defined by the microfabrication process, this approach provides a basis for reproducible magnetic structures across the entire wafer.

Tailoring Magnetic Fields Through Geometric Design

The shape and position of integrated magnets can be adapted to the required magnetic field distribution.

Combined with computer simulations, this allows the magnet geometry and the device to be co-designed during the development phase.

Using Critical Magnetic Materials More Efficiently

Local integration means that magnetic material is only used where a magnetic field is actually required.

This creates the potential to significantly reduce the consumption of rare-earth materials compared with solutions using larger, externally mounted permanent magnets.

Enabling Integration at Later Stages of the Process Flow

ALD-based consolidation does not require conventional high-temperature sintering.

The comparatively low process temperature allows flexible integration into the manufacturing sequence and offers the potential to incorporate micromagnets into microelectronic devices that have already undergone previous fabrication steps.

Research Projects

Learn more about our related research projects:

PowderGridNDT

Smarties

VollMini

Publications

PowderMEMS – A Generic Microfabrication Technology for Integrated Three-Dimensional Functional Microstructures
Published in Micromachines Journal

Investigation of Wafer-Level Fabricated Permanent Micromagnets for MEMS
Published in Micromachines Journal

Fully Integrated High-Performance MEMS Energy Harvester for Mechanical and Contactless Magnetic Excitation in Resonance and at Low Frequencies
Published in Micromachines Journal

Fully Integrated Back-Biased 3D Hall Sensor with Wafer-Level Integrated Permanent Micromagnets
Published in IEEE MEMS

SOI Integrated Micromagnets for Mechanical Magnetic Field Detection
Published in IEEE Sensors Letters

Wafer-level magnetic field biased single domain soft magnetic layers by integrated NdFeB micromagnets
Published in Applied Physics Letters

PowderMEMS® magnets as enabler for miniaturized NV based quantum sensors and quantum processor architectures
Published in Micro and Nano Engineering

Study on the Thermal Stability of Monolithically Integrated PowderMEMS® Magnets for Microelectronic Components
Published in Rahmen des MikroSystemTechnik Kongress 2025

AMR Sensor With Substrate-Integrated PowderMEMS Permanent Magnets for In-Plane Biasing
Published in IEEE Sensors Journal 

Enabling technology: PowderMEMS® microfabrication
Published in IVAM INNO

Press Release from Fraunhofer ISIT: Ion Traps for Quantum Computing