Planar Transformers for High-Power-Density Power Converters

Higher power densities require new transformer designs

Power converters need to become more compact, lighter, and more powerful. Conventional wire-wound transformers are reaching their limits, partly due to their physical size and heat dissipation challenges. Additionally, the winding process affects the precision and reproducibility of manufacturing.

Planar transformers replace traditional wire windings with flat conductor structures, such as those on printed circuit boards or copper foils. This enables compact geometries and reproducible windings. At the same time, parasitic electrical properties can be taken into account more specifically during the design phase.

However, as power increases, a new challenge arises: heat must be reliably dissipated from the layered structure. Although planar transformers generally allow for efficient heat dissipation due to their geometry, thermal hotspots can form inside them. Printed circuit board and insulation layers limit heat transfer out of the laminate structure.

Research therefore addresses two key development goals: further increasing power and power density, as well as designing for greater resource efficiency over the entire life cycle.

In addition to electrical and thermal properties, reparability, reusability, reconfigurability, and the recovery of components and materials are becoming increasingly important.

Jointly Advancing Electrical Optimization, Cooling, and Circulatory Capability

Our research does not view planar transformers merely as magnetic components. We examine their electrical design, thermal behavior, and structural configuration in an integrated manner. Our work focuses on three main lines of research.

Systematically Optimizing Transformer Designs

We are investigating a wide range of possible design variants for high-frequency planar transformers. Using Pareto optimization, we compare different designs in terms of their objective functions.

This allows us to systematically evaluate trade-offs between different requirements and identify suitable design variants for each specific application.

Dissipate heat directly from the layered structure

As power density increases, the thermal challenge shifts to the interior of the transformer. That is why we are researching concepts for integrated liquid cooling that dissipate heat directly from the laminated core.

We are investigating various design approaches, including hollow conductor structures and a cooling concept using plastic spacers. A patent application is pending for the concept using plastic spacers.

The goal is to address the thermal bottleneck inside the transformer more effectively and thereby enable higher power densities.

Designing Modular and Reconfigurable Planar Transformers

Another research approach applies principles of the circular economy to transformer design. To this end, we are investigating a modular, printed-circuit-board-based design.

Standardized layouts are intended to enable different connection configurations, such as series and parallel connections or architectures with multiple windings. This opens up new approaches for reconfiguration, reuse, repair, and the replacement of individual components.

The goal is to more closely integrate requirements for electrical and thermal properties with a consideration of the entire product life cycle in the future.

Combining Digital Design and New Layout Concepts for Planar Transformers

The development of planar transformers requires a holistic approach to electrical, thermal, and design requirements. To achieve this, we combine digital design methods with new concepts for construction and cooling.

This allows us to balance different requirements early in the development process and design transformer concepts specifically for higher power densities and various system requirements.

Planar Transformers for Compact, High-Power Energy Converters

Planar transformers are particularly attractive for applications that require a combination of high power density, compact designs, and reproducible electrical characteristics. The approaches developed for design optimization, liquid cooling, and modular construction are being examined collectively as part of the BRICS project.

Electromobility

The demand for compact, high-power-density power converters is growing in electric vehicles. Planar transformers offer potential for this in isolated DC-to-DC converters and other power electronic converter systems.

Data Centers

The high power density of modern data centers is placing increasing demands on compact and efficient power supply systems. Planar transformers enable flat designs and provide opportunities for intensive cooling as power densities increase.

Solid-State Transformers

Solid-state transformers combine power electronic converters with galvanic isolation, thereby placing higher performance demands on magnetic components. The development of higher-power planar transformers is therefore also relevant for these systems.

Isolated DC-DC Converters

Modular and reconfigurable transformer structures are being investigated for isolated DC-to-DC converters. Series and parallel connections, as well as multi-winding concepts, make it possible to adapt the transformer design to different system architectures.

BRICS

The BRICS project takes a comprehensive look at three research approaches: design optimization, integrated liquid cooling, and cycle-oriented transformer design. The goal is to combine electrical and thermal performance with new approaches to the transformer’s life cycle.

Considering Power Density, Reproducible Design, and Resource Utilization Together

Planar transformers offer design advantages over traditional wire-wound transformers. Our research efforts are aimed at further developing these properties while addressing current limitations in heat dissipation and lifespan.

Compact and slim design

The flat winding structure enables the production of transformers with a low profile. This makes it possible to develop magnetic components specifically for applications where installation space and power density are critical.

Reproducible winding geometries

PCB-based windings have clearly defined geometric structures. This supports reproducible manufacturing and makes it possible to more accurately predict parasitic electrical properties as early as the development stage.

Dissipate heat closer to where it is generated

The integrated liquid cooling system addresses thermal hotspots within the laminated core structure. Instead of dissipating heat exclusively through external surfaces, it is designed to absorb heat closer to where it is generated.

This creates the potential for higher power densities without correspondingly increasing the thermal load inside the transformer.

Systematically weigh different requirements against one another

Pareto-based optimization makes it possible to examine numerous design variants and highlight trade-offs between different design parameters. This allows the transformer design to be tailored more precisely to the specific application.

Enable Reconfiguration and Reuse

Modular PCB-based structures open up possibilities for configuring transformers for different circuit configurations and winding architectures. At the same time, they provide a starting point for the repair, reuse, replacement, and future refurbishment of individual components.

Take the Life Cycle Into Account Early in the Design Process

The integration of circular economy principles goes beyond traditional electrical and thermal optimization. The goal is not only to optimize planar transformers for operation, but also to take reparability, reuse, and material recovery into account during the design phase moving forward.

Research Projects

Learn more about our related research projects:

BRICS

Re-SCHIFF

Super-HEART

Publications

In-Depth Review of Planar Transformer Modeling and Optimization: Challenges and Perspectives
Publication im IEEE Transactions on Power Electronics

Planar Transformer With Integrated Direct Liquid Cooling
Publication im IEEE Transactions on Power Electronics

Circular Economy Oriented and Reconfigurable Planar Transformer Design for Isolated DC/DC Converters
Publication im Rahmen der PCIM Europe 2024