PowderMEMS®: Integrating Functional Materials into Microsystems

Integrating More Material Functionalities into MEMS

Microelectromechanical systems (MEMS) utilize a wide range of physical and chemical effects. Accordingly, they require a diverse selection of functional materials. In addition to semiconductors and metals, these may include magnetic materials, ceramics, polymers, and other functional materials.

Material Diversity Meets Standardized Manufacturing

This diversity presents a fundamental challenge for MEMS fabrication. Developing a separate integration process for each material increases process complexity and development effort.

At the same time, MEMS should ideally be manufactured using reproducible and scalable processes, similar to those established in semiconductor technology.

Decoupling Materials from Manufacturing Processes

There is therefore a need for a process that can integrate a wide variety of starting materials according to a common principle.

Rather than adapting the entire manufacturing process to a specific functional material, the material should be introduced in a form that can be processed using a shared process flow.

Bringing New Functionalities Directly onto the Chip

Integrating functional materials directly into the MEMS substrate also creates opportunities to provide additional functionalities within a compact chip architecture.

Examples include localized magnetic fields, magnetic actuators, magnetic cores for coils, optically active structures, and porous surfaces for sensing and analytical applications.

Using Powder as a Common Starting Point for Different Functional Materials

PowderMEMS follows a material-independent integration approach. Different functional materials are initially provided in powder form and subsequently incorporated into pre-structured silicon or glass substrates using the same fundamental process flow.

Precisely Filling Microcavities with Powder

First, defined microcavities in the substrate are filled with the desired powder.

The morphology of the starting material plays a key role. Particle size, particle shape, and flow properties influence how uniformly and completely fine cavities can be filled.

We therefore systematically investigate which powder characteristics are suitable for different geometries and functional materials.

Connecting Loose Particles Using Atomic Layer Deposition

After filling, the powder particles are interconnected using atomic layer deposition (ALD).

At comparatively low process temperatures, a thin coating forms on the particles. This transforms the loose powder into a mechanically stable three-dimensional microstructure.

A prerequisite is that the starting material can withstand the ALD process without being damaged.

Harnessing Porosity as a Functional Property

Due to their particulate structure, PowderMEMS components are intrinsically porous and feature a large internal surface area.

This property is not merely a consequence of the manufacturing process but can itself be exploited functionally. For example, the internal surface area can be used for heat transfer, mass transport, or interactions with gases and liquids.

Further Functionalizing Internal Surfaces

The large internal surface area can also be coated with additional materials.

Depending on the application, this enables the creation of hydrophobic or catalytically active surfaces, for example. As a result, the same fundamental PowderMEMS structure can be adapted to a wide range of different applications.

Combining Powder Integration with Established MEMS Fabrication Processes

PowderMEMS combines specialized processes for handling loose powders with established microfabrication techniques. The core processes are carried out in a dedicated laboratory environment. Following appropriate conditioning, the substrates can subsequently be reintegrated into existing MEMS process flows.

Reproducibly Filling Microcavities with Powder

Specialized equipment and measurement methods for filling microcavities have been developed within the Fraunhofer-Gesellschaft.

These support both the powder filling process and the monitoring of filling quality.

Mechanically Stabilizing Microstructures Using ALD

Commercially available ALD equipment is used for atomic layer deposition.

The ALD process coats the powder particles introduced into the cavities, thereby bonding them into mechanically stable three-dimensional structures.

Using Silicon and Glass Substrates

The microstructures required for PowderMEMS can be fabricated on different substrate materials.

Substrates featuring suitable microcavities are provided through Fraunhofer ISIT's cleanroom infrastructure or by external partners. This allows PowderMEMS to be combined with a variety of upstream structuring processe

Further Processing of PowderMEMS Structures

Since the core processes involve handling loose powders, PowderMEMS fabrication is carried out in a separate laboratory.

Following specialized conditioning, the processed substrates can subsequently undergo further fabrication using almost all suitable equipment available in the cleanroom and laboratories.

Additional capabilities for subsequent development include:

  • MEMS fabrication processes
  • Wafer- and chip-level characterization
  • Device testing and analysis
  • Chip packaging

Material Properties Determine Functionality

PowderMEMS is not limited to a single application or material class. The functionality of each microstructure is largely determined by the powder used and the design of the structure. This enables a broad range of applications, spanning magnetics and sensing to light emission, as well as chemical and biological analytical processes.

Micromagnets for Sensors and MEMS

Hard magnetic powders such as neodymium-iron-boron (NdFeB) and samarium-cobalt (SmCo) can be processed into integrated micromagnets.

These localized magnetic field sources are of particular interest for Hall-effect sensors and magnetoresistive sensors. Further applications include MEMS devices in which forces are transmitted without physical contact or magnetic actuators are integrated.

Magnetic Fields for Quantum Sensors

Quantum sensors based on nitrogen-vacancy (NV) centers also require precisely defined bias magnetic fields.

Integrated micromagnets offer a potential approach for providing these magnetic fields directly at the sensor in a compact and precise manner.

Potential applications for such quantum sensors range from navigation-independent sensing systems to medical diagnostics and motion tracking.

Integrated Coil Cores

Soft magnetic powders can be used to fabricate magnetic cores for integrated coils.

The intrinsic porosity of PowderMEMS structures can additionally support heat dissipation.

Light-Emitting Microstructures

Phosphor powders can be integrated into PowderMEMS structures to create light-emitting microstructures.

Here, too, porosity can be utilized for effective thermal management of the structure.

Integrating Mass for Energy Harvesters

In one project, tungsten structures were used to increase the mass of a free-standing, movable microstructure.

This demonstrates that PowderMEMS can also be used in applications where a high local material density is required for the mechanical functionality of a MEMS device.

Protecting Sensors Against Particulate Contamination

The porosity of the structures allows gases or liquids to pass through while retaining larger particles.

A demonstration using a humidity sensor showed that PowderMEMS structures can serve as protective caps for sensors that need to interact with their environment while remaining sensitive to particulate contamination.

Liquid Chromatography

The large internal surface area and porous structure also make PowderMEMS suitable for separation processes.

In an internal project, the structures were investigated for liquid-phase chromatography, demonstrating a separation effect.

Extracting DNA from Samples

In a regional research project, PowderMEMS structures were used to extract DNA from saliva samples.

This demonstrates that the platform can support not only physical functionalities but also biological and chemical applications.

Integrating Different Functional Materials Using a Common Process Concept

The key advantage of PowderMEMS lies in separating material functionality from the fundamental manufacturing process. Different powders can be integrated into MEMS using the same basic approach of cavity filling and ALD-based stabilization.

This enables the investigation of new material functionalities without having to develop an entirely new integration method for each material class.

Placing Functional Materials Directly Within the Chip

Magnetic and other functional materials can be integrated precisely where their effects are required.

For magnetic field sensors, for example, this makes it possible to integrate the magnetic field source directly into the sensor chip. Separate magnetic components and additional assembly steps can therefore be reduced.

Reducing the Size of Sensor Systems

When micromagnets or other functional structures become an integral part of the chip, they no longer require additional external space.

This creates opportunities for more compact sensor and MEMS systems.

Using Critical Materials More Efficiently

Integrated micromagnets enable a significant reduction in the consumption of critical rare-earth materials compared to larger external magnets.

The magnetic material is used only in the specific locations where the required magnetic field needs to be generated.

Leveraging Porosity as an Additional Functionality

Due to their particulate structure, PowderMEMS components feature a large internal surface area.

This can be utilized for improved heat transfer, interaction with liquids or gases, and separation and extraction processes.

Tailoring Surface Properties to the Application

The internal surface of the porous microstructure can be functionally modified after fabrication.

Depending on the application, the same basic structure can, for example, be given hydrophobic properties or coated with catalytically active materials.

Accelerating the Evaluation of New Materials for MEMS

Since PowderMEMS can integrate different powdered starting materials using a common process flow, new material classes can be investigated and compared more systematically within MEMS structures.

This expands the available material portfolio for developing new sensing, actuation, and analytical functionalities.

Research Projects

Learn more about our related research projects:

PowderGridNDT

Smarties

VollMini

Publications

Learn more about the development of PowderMEMS technology.

Read Here